Important Plumber Tips for Bathtub Installation
Important Plumber Tips for Bathtub Installation
Blog Article
Have you been on the lookout for advice about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and often, tiling skills. Changing an old tub with a new one is likewise a moderately difficult project. If the old bathtub is readily obtainable, the task can move immediately; if you need to open a wall surface to remove the old bathtub and place the brand-new bathtub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will require an assistant to leave the old bathtub and set in the brand-new one. See to it you have certified on your own for the work and also are comfortable trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to think about employing one prior to you begin. Opportunities are you may require a specialist plumber to make tube connections.
This article will assist you set up a brand-new bathtub in your shower room if you have actually already bought a brand-new tub as well as don't need to transform the arrangement of your previous water system pipelines.
Your devices and product list must make up the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bath should be fitted (if called for) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps device to stop strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps making use of 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final setting.
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, switch on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be rather bothersome due to the restricted gain access to that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this process. As soon as the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wood boards under its feet, put the tub in the called for placement. The wood boards are useful in evenly spreading out the weight of the bathtub over the location of the boards instead of focusing all the weight onto four little points.
The next goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bathtub till the level reads level.
To mount taps, fit the bottom of the outermost flexible faucet adapter to the proper supply pipeline by making a compression join; after that do the exact same for the other faucet.
Activate the water system and examine all joints as well as brand-new pipework for leaks and also tighten them if required. Load the bathtub as well as also inspect the overflow electrical outlet as well as the regular outlet for leaks.
Ultimately, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait up until the tub has actually been made use of at least once as this will settle it into its final placement.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, position the tap in the installing hole in the bath/basin guaranteeing that the washing machines are in place in between the faucet as well as the sink. Safeguard the tap in place with the manufacturer offered backnut. Once the faucet is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, creating the water to pass through the wall in between the bathroom and the tiling, causing difficulties with moisture and possible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also fittings. They are sold in tubes and cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill the bathtub with water before securing, to enable the motion experienced when the bathtub remains in use. The sealant can fracture fairly early if you do not take into account this motion before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise conveniently offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was introduced to that article about Tools You Need to Install a New Bathtub from an associate on a different site. Do you know someone else who is looking into the subject? Take a moment to share it. I appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Plumbing integrity assured. Report this page